G1/2 Thread Probe DS18B20 Temperature Sensor for Solar Water Heater

DS18B20 Instead of reading a voltage with an analog pin, we read a serial stream of bits from the sensor on one of our digital pins. One such sensor is the Dallas Semiconductor DS18B20. It uses what Dallas Semiconductor calls the OneWire protocol to communicate back and forth between the sensor and the tiny computer. It has three pins, one for power, one for ground, and one for the data link (it is this single data link line that gives the protocol its name).

DS18B20 is a commonly used digital temperature sensor, and its output is digital signal. It has the characteristics of small size, low hardware overhead, strong anti-interference ability and high precision.

Votesen VTS200 is a DS18B20 digital temperature sensor which composed of original DALLAS chip, stainless steel probe, cable and connector.

1. Digital Signal Output

One Wire interface requires only one port pin for communication. Requires no external components.

2. High Accuracy

Operating temperature range: -55°C to +125°C (-67F to +257F), ±0.5°C accuracy from -10°C to +85°C.

3. Data Line Power Supply

Can be powered from data line. Power supply range is 3.0V to 5.5V.

4. Fast Response

Thermometer resolution is programmable from 9 to 12 bits.

5.Various Probe Design

Stainless steel protection pipe diameter φ 6

Suitable for DN15~25, DN40~DN250 various media industrial pipe and small space equipment temperature measurement.

Thread M10X1, M12X1.5, G1/2 ",G1/8"

Send us the below details and we will be able to assist you based on your requirements.

1. Operation Temperature range

2. Application

3. Probe Dimension

4. Types of Probe

5. Cable Length

5. Cable Connector

6. Any other specific request

This product is widely used in boiler temperature measurement, room temperature measurement, agricultural greenhouse temperature measurement, clean room temperature measurement, freezer, granary, storage tank, telecommunications room, power room, cable trough temperature measurement control field. Bearing bush, cylinder block, spinning machine, air conditioning, and other small space industrial equipment test temperature control. Heating/refrigeration pipeline heat metering, central air conditioning and industrial temperature measurement control.

Q: Where physically on the device does the temperature measurement take place?

A: The DS18B20 does not sense temperature directly through the package. For all package types, the DS18B20 senses temperature primarily through the GND pin. Ensuring a good thermal connection between the GND pin of the device and the heat source you wish to measure will provide the best results.

Q: Is there a way to extend the temperature range of the DS18B20?

A: No, there is not a way to increase the range it reads. The DS18B20 reads with an accuracy of ±0.5°C from -10°C to +85°C and ±2°C accuracy from -55°C to +125°C.

Q: Will a conformal coating affect the thermal response of the DS18B20?

A: A thin conformal coating will not affect the thermal response of the device.

Q: Using OneWireViewer, can more than one DS18B20 be logged?

A: Yes, every DS18B20 will have a file where you can store the data. Data will be received from one DS18B20 at a time.

Q: Can you power the DS18B20 from a 3V battery?

A: The DS18B20 can be powered from any source. Since batteries will dip in voltage, a nominal 3V battery may not always supply the minimum 3.0V the DS18B20 requires. We suggest a step-up voltage regulator is used to ensure the device is supplied within its rated voltage range of 3.0V to 5.5V.

XI'AN VOTESEN ELECTRONIC TECHNOLOGY CO.,LTD located in XI'AN CITY, one of the three major sensor industry based in China. We have more than 10 years experiences in sensor industry. We are not only the product manufactory, but also a professional technical support team which we can accommodate customer various requirements. We have produced thousands kinds of especially temperature and humidity sensors. We have strong customization capabilities to meet the different customization needs. We welcome you to share your idea and request with us. Other than customization, we also provide OEM/ODM service for you.

Votesen is committed to produce high-quality sensor and measurement instruments. Our mature and advanced production technologies ensure your project safety, stable and long lasting operation. Our ultimate goal is to ensure and control the quality of our products in line with the industry highest standard quality. Our products have been sold to over 40 countries like Australia, USA, Canada, Mexico, Netherland, Germany, Russia, Poland, Korea, India etc. and we have cooperated with many well-known enterprises. We have served more than 100,000 partners so far. Our products are widely used in a various industries, such as Medical, Petrochemical, Internet of Things Intelligent Monitoring, Food and Beverage Industry, Automotive, Livelihood Supplies and other different fields.